Warne Mountain Tech 30 mm Ultra High Rings

7217M_Warne_Mountain-Tech-Rings.jpg
Warne_Mountain-Tech-Rings-1.jpg
7217M_Warne_Mountain-Tech-Rings.jpg
Warne_Mountain-Tech-Rings-1.jpg
sale

Warne Mountain Tech 30 mm Ultra High Rings

Sale Price:$125.00 Original Price:$146.99

Lightweight and element proof

SKU 7217M

We engineered Warne Mountain Tech as a lightweight and rugged scope ring design that is equally at home on a mountain rifle or precision target rifle. Featuring 7075 aluminum construction and stainless hardware to withstand the punishing conditions Mother Nature can dish out.

Precision CNC machined from 7075/T6 aluminum for a high strength & lightweight platform

  • Mil-Spec hardcoat anodized finish for abrasion and corrosion resistance.

  • Rings feature stainless steel hardware for “Element Proof” protection.

  • Mil-Spec 65 in/lb., 1/2″ tactical nut attachments for securely clamping to the rail.

  • Fits Picatinny & Weaver style mounts and are NATO-STANAG compatible.

  • Available for 1″, 30 and 34mm tube sizes; in Low, Medium, High and MSR ideal height; For maximum compatibility with most scope/firearm combinations.

The credo of the backcountry hunter.When tired legs are the only mode of transportation. When the air feels thin, and feet feel heavy. When months of preparation, training and sleepless nights thinking about the upcoming hunt culminate into a single moment, placing the crosshair where it needs to be for the perfect shot. Warne Mountain Tech is the ultimate lightweight precision scope mounting system. Don’t leave your dream hunt to chance. When every ounce matters, and every shot counts, Warne Mountain Tech are the scope mounts you can depend on.

Add To Cart

Instructions

Always verify that your firearm is UN-LOADED before performing any service on it. Warne recommends that you loosely assemble rings and scope onto firearm prior to final mounting to verify eye relief and ring spacing.

  • Loosen both nuts on the Mountain Tech rings and install on your Mountain Tech rail or Maxima (weaver style) bases.

    1. Slide each ring forward so the recoil lug is contacting the front of the cross slot. Torque the ring nut to 65 in/lbs maximum and repeat for the other ring.

    2. Remove the four cap screws from each top cap with the supplied T-15 wrench and remove top caps.

    3. Place your scope in the Mountain Tech rings and replace top caps and screws*.

    4. With the scope still loose in the rings, adjust the scope for eye relief and correct orientation of the reticle.

    5. Finally, tighten the cap screws in a criss-cross pattern to scope manufacturers’ recommended torque rating**, 18 in/lb maximum.

    6. To remove the scope, simply loosen the ½” nut and lift the scope off the mount, tilting slightly to the opposite side of the nut.To re-mount the scope, simply place the rings into the slots the scope was originally mounted in, slide the rings and scope forward until the recoil lugs contact the front of the slot, and tighten the ½” nut.

    7. NOTE: The ½” tactical nut screw assembly is pre-set at the factory and does not require any adjustments. Tampering with this screw can cause improper function of the scope rings.

      *Torque Spec are for dry threads, DO NOT USE THREAD-LOCKER COMPOUND

      **Many scope manufacturers’ have established specific torque ratings for their scope and you must follow their recommended torque.

      IMPORTANT: NEVER OVER TIGHTEN ANY BASE OR RING SCREW. NEVER ATTACH A SCOPE IF THE OBJECTIVE TOUCHES THE BARREL OR CAUSES INTERFERENCE WITH THE BOLT, SAFETY OR CYCLING OF THE ACTION. ALWAYS FOLLOW THE FIREARM OR SCOPE MANUFACTURERS’ RECOMMENDED TORQUE SPECIFICATIONS. YOU ARE RESPONSIBLE FOR YOUR OWN GUNSMITHING METHODS.

                  ⇒ If you are unsure or do not have the proper tools, please contact a gunsmith for assistance, Warne will not be held liable for stripped/damaged receivers or scopes.



BOOK NOW